Tap Repairs in Hendra
A drip in the basin is one worn part asking to be replaced, and a slow drip can waste thousands of litres of water over time. Tap repairs in Hendra usually come down to a washer, a cartridge or an O-ring.
If we're late, $100 comes off your bill
- Licensed and InsuredEvery job done by a licensed plumber. QBCC No: 15024607
- Fixed Quote FirstFlat-rate pricing, agreed before any work starts
- Lifetime Labour WarrantyBacked by our Fix-It-or-It's-Free guarantee (T&Cs apply)
- $0 Call-Out FeesNo extra charge for nights, weekends or public holidays
A licensed plumber can name the culprit from the tap type and where the water shows. Hendra Same Day Plumbing handles these fittings across Hendra and the streets nearby, with a fixed quote before any work starts.
How Tap Type Decides the Repair
Washer taps close off the flow with a rubber washer pressing onto a metal valve seat; mixers do it with a ceramic disc cartridge. Knowing which one is on your basin tells you what the repair involves before anyone opens a toolbox.
The classic washer tap has separate hot and cold handles, each taking several turns to open or close. Inside, the jumper valve is the small brass piece at the spindle's lower end that pushes the washer down onto the seat.
A mixer runs hot and cold through one lever, usually a quarter turn, with two polished ceramic discs sliding against each other inside the cartridge. When those discs wear out, the fix is a complete cartridge swap, matched to the tap's make and model, because sizes and fittings vary between them.
A handle that sticks or grinds is usually grit or wear in the working parts, even when the tap still seals. That symptom sits on the same visit as the drip.
Still Dripping After You Turn It Off
Water still leaving the spout once you've closed the tap right down means the part that seals has worn through. On a washer tap the culprit is the washer, the seat, or both; on a mixer it's the cartridge.
The leak's position names the failed part:
At the spout, tap closed
the washer and seat on a washer tap, or the cartridge on a mixer.
Around the handle, tap open
an O-ring or the seal on the spindle has perished.
At the base or under the bench
worn O-rings, a connection underneath that has come loose, or a crack in the tap body itself.
Each tap should have an isolation valve nearby that shuts that one fixture alone. Where no isolation valve exists, the water comes off at the meter instead, and we check first that no appliance, the hot water system included, depends on the supply staying on.
Tap Repairs for Owners and Tenants
Queensland draws a sharp line around who may do tap work. The QBCC's unregulated list includes exactly one tap task: renewing a washer, or the jumper valve that holds it.
Anyone with the needed knowledge and skill may do that task, provided the finished work still meets the standards. Everything past that point needs a licence.
Putting on a whole new tap is licensed work, and the QBCC guide uses that very job as its example of what an owner cannot take on alone. Other tap repairs count as minor work: a licensee carries them out, and nothing needs lodging with the QBCC.
Renters have a simpler path. A dripping tap sits outside the Act's emergency repairs, which makes it routine: the tenant tells the owner or manager, who then arranges the fix within a reasonable period. If nothing happens, a Notice to remedy breach (Form 11) from the Residential Tenancies Authority starts a seven-day clock for the repair.
Tap Wear in an Old Suburb
Hendra's housing stock is old and staying that way. Area-level figures show just 95 dwellings approved across five years, against 1,771 homes counted at the last census, so most basins and laundries still carry fittings that went in decades ago.
That age shows up in the taps themselves. Washer taps from the postwar build-out around Derby Street and its neighbours have had spindles turned thousands of times, and seats that have been machined once already may not take a second reseating. Galvanised pipe remnants in the older walls can leave grit in the supply that chews through washers faster than clean water would.
Our tap and toilet work covers the full range of these fittings. Running toilet repairs handles the cistern faults that often arrive alongside a worn tap. Choosing a new tap takes over when a body has reached the end.
What Affects the Cost of a Tap Repair
The price turns on four things: the tap type, the part it needs, damage to the seat or body, and how easily the water shuts off. A cracked or badly corroded body pushes the job from repair to replacement, and a drip that survives fresh washers and cartridges points the same way.
Doing several taps in one visit changes the figure as well, since the isolation and setup happen once. We set the price in a written quote after inspecting the tap, so you approve the real number before anyone picks up a spanner.
How a Tap Repair Visit Runs
- 1
Describe the problem
Phone (07) 3523 7172 or fill in the form with what you're seeing in Hendra. The more we know, the better we can prepare.
- 2
We strip and diagnose the tap
With the water isolated, we pull the tap down to the washer, cartridge or O-ring, check the seat and body for damage, and quote on the true fault rather than a guess.
- 3
Agree on the price
A fixed quote comes before any work starts: flat-rate pricing, no hidden fees, and your go-ahead first.
- 4
Pay on completion
Card or EFTPOS on site when everything's working, or ask us about Fix now, pay later.
Plumbing job in Hendra?
$0 call-out fees, available 24/7, and same-day where we can.
Tap Repair Questions From Hendra
Call (07) 3523 7172How do I stop my tap from dripping?
Find the sealing part first. On a washer tap that means the washer and its seat; on a mixer it means the ceramic disc cartridge. In Queensland only the washer and jumper valve are unregulated DIY tasks, and every other tap repair, including any new tap, needs a licensed plumber.
What makes a mixer tap leak from the base?
Worn O-rings are the usual cause. Below the tap, a connection that has loosened can seep, and a crack through the body does the same. A plumber isolates the water, strips the mixer, and swaps the failed part or the whole cartridge.
How much does it cost to fix a leaking tap in Hendra?
The price depends on the tap type, the part needed, seat or body damage, how easily the water shuts off, and how many taps we do. You get the figure in a written quote once the tap has been inspected, and the number you approve is the number you pay.
Is it worth repairing an old tap in Hendra?
Yes, if the body is sound and the fault is a worn washer, O-ring or cartridge. A body that is cracked or badly corroded, or a leak that survives new parts, means the tap has reached the end and replacement is the better spend.
Will turning the tap off harder stop the drip?
No, forcing the handle down makes things worse. It drives the washer into the seat and wears both faster, and on a mixer it can crack the cartridge. Replacing the worn part is the only lasting fix.
Book Your Tap RepairWe'll call you back.
Book on (07) 3523 7172 for plumbing anywhere in Hendra. We're available 24/7, there's no extra charge for nights, weekends or public holidays, and every job comes with $0 call-out fees.
To claim your $0 call-out fee, call (07) 3523 7172 today.